Cable & Satellite Company Technicians Will Leave You With A Wiring Mess



image of tv hung on wall with a wiring mess


When planning for wall mounted TV's at your residence do not rely on the Cable Company or Satellite provider to leave you with a clean tidy wiring job after their installation. If you have not properly planned for the design of your TV system you can easily end up with a sloppy installation that usually only a certified electronics contractor can help you with. Your local electrician can sometimes help with these issues but depending on their experience they can get your TV hung on the wall but the necessary details and proper wiring requirements are often over looked.



To properly plan hanging TV's on your wall it is highly recommended contacting a local electronics contractor that can properly implement an installation for you and also be able to provide future service to your system as you may need help down the road.


image of tv hung on wall with a wiring mess




Comments

Post a Comment

Popular posts from this blog

How to Wire Crestron Cresnet Connections

Image
To wire Crestron Cresnet properly you are suggested to use Crestron's standard Cresnet cabling which consists of 4 conductors to operate correctly. You will need a small flat head screw driver called a tweeker to unscrew the 4 small screws of the green phoenix connector to be able to insert your stripped back wire ends.  The Red wire is for the power of the Cresnet communication bus which is 24VAC.  The White wire is the Y communication of the RS-485 bus which is the positive side of communication pair.  The Blue wire is the Z communication of the RS-485 bus and this is the negative side of the bus pair.  Finally the Black wire is the ground side of the power pair to complete the Cresnet connections and wiring.  Once the wires are inserted into the Pheonix connector you will use your tweeker screw driver to fasten the wire to the phoenix connector as seen below in the picture to be able to connect whichever device you are hooking up.  Crestron Cre
Keep reading

How to Control NVIDIA Shield with IR (Infrared)

Image
When attempting to control and integrate an NVIDIA Shield with the use of a universal control you will need the help from the Flirc USB Dongle to accomplish the task which is readily available on Amazon's Online Store .  When setting up the Flirc adapter you are able to configure the USB dongle and learn the IR codes that you would like to use to control your NVIDIA Shield with the downloadable Flirc configuration software. The Flirc dongle and software together learn the IR codes from any remote and allow them to control the functions of the NVIDIA Shield which are set one at a time.  Once the setup has been completed with all the IR codes learned into the Flirc adapter you finalize the configuration and the dongle is ready to be plugged into the NVIDIA Shield in an open usb port. Essentially now you have an IR receiver located off the usb port for you to use as you wish. The Flirc USB dongle also is compatible in controlling Amazon Fi
Keep reading

How to Control Amazon Fire TV with IR (Infrared)

Image
When attempting to control and integrate the Amazon Fire TV with the use of a universal control you will need the help from the Flirc USB Dongle to accomplish the task which is readily available on Amazon's Online Store .  The Amazon Fire TV comes with a Bluetooth remote which is great if you do not have an involved TV setup and would like to hide the Fire TV away out of viewing site but it does not help if you are trying to have one system and remote control to work all your devices seamlessly. This is where integrating the Fire TV using the Flirc USB comes into play. When setting up the Flirc adapter you are able to configure the USB dongle and learn the IR codes that you would like to use to control your Fire TV with the downloadable Flirc configuration software. The Flirc dongle and software together learn the IR codes from any remote and allow them to control the functions of the Fire TV which are set one at a time.  Once the setup has been com
Keep reading

How to Reboot a Crestron Processor Remotely

Image
1.  The first step to reboot a Crestron processor remotely is to setup and connect to the remote network with a VPN connection where the Crestron system you are working on resides. Setting up a VPN connection is beyond the scope of this article but this connection can be done utilizing a VPN router and a dynamic DNS service. 2.  Once you have a successful VPN connection you can now open the Crestron toolbox program to initiate your connection to the processor. Within the Toolbox program open the text console and connect to the processor that you would like to reboot. Having an address entry for your processor will help streamline connecting to your processor. This can be done using the address book button located in the lower left of the text console. Once your address entry is complete you can simply select the correct entry in the drop down address box.  3.  Upon connection to the processor within the text console you will see the model number of your proces
Keep reading